What Does F1 Mean On Hot Tub?

On page 29 it shows that “F1” indicates the spa is running the factory default 1 hour filtration cycle. It indicates this should run one 30-minute cycle every 12 hours. If your spa is set to the F1 filtration option, and is activating more than once every 12 hours, there may be an issue with it’s controls/brain.

What Does Fc Mean On A Hot Tub?

freeze condition

How Do I Reset My Hot Tub Control Panel?

How to Reset a Spa Heater

Locate the spa’s high-limit reset. This is a red button found on many spa packs. Press the high-limit reset button. Turn on your spa and observe its operation. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

What Does F2 Mean On A Hot Tub?

The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. There are a few things you can look for when trouble shooting an F2 error code on your hot tub.

What Does Fl Code Mean On A Hot Tub?

Today’s post is about water flow trouble codes on your spa panel. These are usually presented as FL, FLO or FLOW on your display, although it may appear as LF (Low Flow) or PS (Pressure Switch). When the water isn’t flowing like it should, the heater stops working, equipment overheats and water quality quickly suffers.

How Far Should A Hot Tub Be From The House?

Having your hot tub right next to the wall of your home is probably too close. The steam that comes from the water may seep into windows and water splashed from the tub may cause a slippery walkway. A few feet away from your home and a few feet away from your walkway is typically the ideal combination.

How Do You Fix The Error Code On A Hot Tub?

How to Troubleshoot a Hot Tub FLO Error Code Shut down the spa at the breaker. Make sure there is no debris in the water that can get sucked into the pump. Take out all of the filter(s) and set them aside. Turn spa back on at the breaker with the filters out.

How Do I Reset My Hot Tub Jacuzzi?

Reset “616” Code on 2012-2013 J-300 & LX Collection Models: Press and hold the Jets pump 1 and Cooler (-) button at the same time for 3 seconds. Press the Warmer (+) button until the display shows “0”. If the timer has reached “0”, pressing the Jets pump 1 button will reset the counter.

What Is Ec Code On Hot Tub?

Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is sampled Only during Programmed Filter Cycles. Between Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump has not turned ON and the Last Water Temperature is not current.

How Long Does It Take To Heat A Hot Tub?

approximately 4 hours

What Does The Code Hl Mean On A Hot Tub?

HL. When “HL” error message displays, it means the system shut the heater down because temps at the heater reached 119ºF (48ºC). When “HL” error message is flashing, it means the system shut down because the water temps in the spa reached 112ºF (44ºC).

What Does Fil2 Mean On Hot Tub?

Posted on October 30, 2016. An FL2 error code and FL1 error code are often confused for one another. While an FL1 error code means the spa isn’t sensing enough water flow to close the flow switch, the FL2 error code means exactly the opposite.

What Does Ec Code Mean On Hot Tub?

Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.

What Does Hh Mean On Hot Tub?

Heated Heater

Why Wont My Hot Tub Heat Up?

Low flow in your spa or hot tub is most commonly associated with a dirty spa filter. If your spa heater won’t heat, remove and clean the filter(s) rule out a pressure or flow rate problem. Low water level, a clogged pump impeller, closed valves, clogged pipes or blocked spa drain covers can also cause flow issues.

What Does Fl1 Mean On A Jacuzzi Hot Tub?

FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake. When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed.

How Do You Prime A Hot Tub Pump?

There are two methods of priming the pump. Turn the spa on and wait for PR (Priming Mode) to appear on the topside display. Press the JETS button to turn on the pump and let it run for 10 seconds. Press the JETS buttons again and let the pump run in high speed for 10 seconds.

How Do I Test My Hot Tub Control Panel?

No Display on Topside Control Panel Reset Spa Controller, power down and restart. Check for condensation under display glass. Check cable for crimps or any visible damage. Clean plug-in cable connections on both ends. Check power at Transformer on control circuit board. Check power at fuse on spa control circuit board.